View T89C511503_1119189.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* Protocol
- UART Used as a Physical Layer - Based on the Intel Hex-type Records - Autobaud * In-System Programming - Read/Write Flash and EEPROM Memories - Read Device ID - Full-chip Erase - Read/Write Configuration Bytes - Security Setting From ISP Command - Remote Application Start Command * In-Application Programming/Self-Programming - Read/Write Flash and EEPROM Memories - Read Device ID - Block Erase - Read/Write Configuration Bytes - Bootloader Start
80C51 Microcontrollers
Description
This document describes the UART bootloader functionalities as well as the serial protocol to efficiently perform operations on the on-chip Flash memory. Additional information on the T89C5115 product can be found in the T89C5115 datasheet and the T89C5115 errata sheet available on the Atmel web site, www.atmel.com. The bootloader software Package (source code and binary) currently used for production is available from the Atmel web site.
T89C5115 UART Bootloader
Bootloader Revision Revisions 1.0.0
Purpose of Modifications First release
Date 03/12/2001
Rev. 4225B-8051-12/03
1
Functional Description
In-System Programming (ISP) Capability
The T89C5115 Bootloader facilitates In-System Programming and In-Application Programming. In-System Programming allows the user to program or reprogram a microcontroller's onchip Flash memory without removing it from the system and without the need of a preprogrammed application. The UART bootloader can manage communication with a host through the serial network. It can also access and perform requested operations on the on-chip Flash memory.
In-Application Programming or Selfprogramming capability
In-Application Programming (IAP) allows the reprogramming of a microcontroller's onchip Flash memory without removing it from the system and while the embedded application is running. The UART bootloader contains some Application Programming Interface routines named API routines allowing IAP by using the user's firmware.
Block Diagram
This section describes the different parts of the bootloader. Figure 1 shows the on-chip bootloader and IAP processes. Figure 1. Bootloader Process Description
On chip User Application
External Host via the UART Protocol Communication
ISP Communication Management
IAP User Call Management
Flash Memory Management
Flash Memory
2
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
ISP Communication Management The purpose of this process is to manage the communication and its protocol between the on-chip bootloader and an external device (host). The on-chip bootloader implements a Serial protocol (see Section "Protocol", page 9). This process translates serial communication frames (UART) into Flash memory accesses (read, write, erase...). Several Application Program Interface (API) calls are available to the application program to selectively erase and program Flash pages. All calls are made through a common interface (API calls) included in the bootloader. The purpose of this process is to translate the application request into internal Flash Memory operations. This process manages low level accesses to the Flash memory (performs read and write accesses).
User Call Management
Flash Memory Management
Bootloader Configuration
Configuration and Manufacturer Information The following table lists Configuration and Manufacturer byte information used by the bootloader. This information can be accessed through a set of API or ISP commands.
Mnemonic BSB SBV P1_CF P3_CF P4_CF SSB EB Manufacturer ID1: Family code ID2: Product Name ID3: Product Revision Description Boot Status Byte Software Boot Vector Port 1 Configuration Port 3 Configuration Port 4 Configuration Software Security Byte Extra Byte Default Value FFh FCh FEh FFh FFh FFh FFh 58h D7h BBh FFh
3
4225B-8051-12/03
Mapping and Default Value of Hardware Security Byte
The 4 Most Significant Byte (MSB) of the Hardware Byte can be read/written by software (this area is called Fuse bits). The 4 Less Significant Byte (LSB) can only be read by software and written by hardware in parallel mode (with parallel programmer devices).
Bit Position 7 6 5 4 3 2 1 0 Mnemonic X2B BLJB Reserved Reserved Reserved LB2 LB1 LB0 Default Value U P U U U P U U To lock the chip (see datasheet) Description To start in x1 mode To map the boot area in code area between F800hFFFFh
Note:
U: Unprogram = 1 P: Program = 0
Security
The bootloader has Software Security Byte (SSB) to protect itself from user access or ISP access. The Software Security Byte (SSB) protects from ISP accesses. The command "Program Software Security Bit" can only write a higher priority level. There are three levels of security: * level 0: NO_SECURITY (FFh) This is the default level. From level 0, one can write level 1 or level 2. level 1: WRITE_SECURITY (FEh) In this level it is impossible to write in the Flash memory, BSB and SBV. The Bootloader returns an error message. From level 1, one can write only level 2. level 2: RD_WR_SECURITY (FCh) Level 2 forbids all read and write accesses to/from the Flash memory. The Bootloader returns an error message.
*
*
Only a full chip erase command can reset the software security bits.
Level 0 Flash/EEPROM Fuse bit BSB & SBV & EB SSB Manufacturer info Bootloader info Erase block Full chip erase Blank check Any access allowed Any access allowed Any access allowed Any access allowed Read only access allowed Read only access allowed Allowed Allowed Allowed Level 1 Read only access allowed Read only access allowed Read only access allowed Write level2 allowed Read only access allowed Read only access allowed Not allowed Allowed Allowed Level 2 All access not allowed All access not allowed All access not allowed Read only access allowed Read only access allowed Read only access allowed Not allowed Allowed Allowed
4
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Software Boot Vector
The Software Boot Vector (SBV) forces the execution of a user bootloader starting at address [SBV]00h in the application area (FM0). The way to start this user bootloader is described in the section 'Boot Process'. Figure 2. Software Boot Vector
UART Bootloader
User Bootloader Application [SBV]00h
FM1
FM0
FLIP Software Program
FLIP is a PC software program running under Windows(R) 9x//2000/XP, Windows NT(R) and LINUX(R) that supports all Atmel Flash microcontroller. This software program is available free of charge from the Atmel web site.
5
4225B-8051-12/03
In-System Programming
The ISP allows the user to program or reprogram a microcontroller's on-chip Flash memory through the serial line without removing it from the system and without the need of a pre-programmed application. This section describes how to start the UART bootloader and all higher level protocol over the serial line.
Boot Process
The bootloader can be activated in two ways: * * Hardware condition Regular boot process
Hardware Condition
The Hardware Condition forces the bootloader execution from reset. The default factory Hardware Condition is assigned to port P1. * P1 must be equal to FEh In order to offer the best flexibility, the user can define its own Hardware Condition on one of the following Ports: * * * Port1 Port3 Port4 (only bit0 and bit1)
The Hardware Condition configuration is stored in three bytes called P1_CF, P3_CF, P4_CF. These bytes can be modified by the user through a set of API or through an ISP command. There is a priority between P1_CF, P3_CF and P4_CF (see boot process diagram).
Note: The BLJB must ba at 0 (programmed) to be able to restart the bootloader. If the BLJB is equal to 1 (unprogrammed) only the hardware parallel programmer can change this bit (see T89C5115 Datasheet for more detail).
6
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Figure 3. Regular Boot Process
RESET Bit ENBOOT in AUXR1 Register is Initialized with BLJB Inverted
Hardware Boot Process
ENBOOT = 0 PC = 0000h
Yes
BLJB = 1 ENBOOT = 1 PC = F800h
No No
P1_CF = FFh No
Yes
No
P1_CF = P1 Yes
P3_CF = FFh
Yes
Software Boot Process
No
P3_CF = P3 Yes
No
P4_CF = FFh
Yes
No
P4_CF = P4
Yes
BSB = 0
Yes
No No
SBV < 3Fh Yes
Start Application
Start User Bootloader
Start Bootloader
7
4225B-8051-12/03
Physical Layer
The UART used to transmit information has the following configuration: * * * * * Character: 8-bit data Parity: none Stop: 2 bit Flow control: none Baud rate: autobaud is performed by the bootloader to compute the baud rate chosen by the host.
Frame Description
The Serial Protocol is based on the Intel Hex-type records. Intel Hex records consist of ASCII characters used to represent hexadecimal values and are summarized below. Table 1. Intel Hex Type Frame
Record Mark `:' 1 byte Record length 1 byte Load Offset 2 bytes Record Type 1 bytes Data or Info n byte Checksum 1 byte
* *
Record Mark: - - Record Mark is the start of frame. This field must contain ':'. Record length specifies the number of Bytes of information or data which follows the Record Type field of the record. Load Offset specifies the 16-bit starting load offset of the data Bytes, therefore this field is used only for Data Program Record. Record Type specifies the command type. This field is used to interpret the remaining information within the frame. Data/Info is a variable length field. It consists of zero or more Bytes encoded as pairs of hexadecimal digits. The meaning of data depends on the Record Type. The two's complement of the 8-bit Bytes that result from converting each pair of ASCII hexadecimal digits to one Byte of binary, and including the Record Length field to and including the last Byte of the Data/Info field. Therefore, the sum of all the ASCII pairs in a record after converting to binary, from the Record Length field to and including the Checksum field, is zero. Record length:
*
Load Offset: -
*
Record Type: -
*
Data/Info: -
*
Checksum: -
8
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Protocol
Overview An initialization step must be performed after each Reset. After a microcontroller reset, t h e b o o tl o a d e r w a it s f o r a n a u t o b a u d s e q u e n c e ( s e e S e c t io n " A u t o b a u d Performances"). When the communication is initialized, the protocol depends on the record type issued by the host. Communication Initialization The host initiates the communication by sending a 'U' character to help the bootloader to compute the baudrate (autobaud). Figure 4. Initialization Host Init Communication "U" Bootloader
Performs Autobaud Sends Back `U' Character
If (not received "U") Else Communication Opened
"U"
Autobaud Performances
The bootloader supports a wide range of baud rates. It is also adaptable to a wide range of oscillator frequencies. This is accomplished by measuring the bit-time of a single bit in a received character. This information is then used to program the baud rate in terms of timer counts based on the oscillator frequency. Table 2 shows the autobaud capabilities.
Table 2. Autobaud Performances
Frequency (MHz) Baudrate (kHz) 2400 4800 9600 19200 38400 57600 115200 Frequency (MHz) Baudrate (kHz) 2400 4800 9600 19200 8 OK OK OK OK 10 OK OK OK OK 11.0592 OK OK OK OK 12 OK OK OK OK 14.746 OK OK OK OK 16 OK OK OK OK 20 OK OK OK OK 24 OK OK OK OK 26.6 OK OK OK OK 1.8432 OK OK OK OK 2 OK 2.4576 OK OK OK OK OK 3 OK OK OK OK 3.6864 OK OK OK OK OK OK 4 OK OK OK 5 OK OK OK OK 6 OK OK OK OK OK 7.3728 OK OK OK OK OK OK OK
9
4225B-8051-12/03
Frequency (MHz) Baudrate (kHz) 38400 57600 115200 8 10 11.0592 OK OK OK 12 OK 14.746 OK OK OK 16 OK OK 20 OK OK 24 OK OK 26.6 OK OK -
Command Data Stream Protocol Figure 5. Command Flow Host
All commands are sent using the same flow. Each frame sent by the host is echoed by the bootloader.
Bootloader ":" ":" If (not received ":") Else Sends echo and start reception
Sends first character of the Frame
Sends frame (made of 2 ASCII characters per Byte) Echo analysis
Gets frame, and sends back echo for each received Byte
10
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Programming the Flash or EEPROM data The flow described below shows how to program data in the Flash memory or in the EEPROM data memory. The bootloader programs on a page of 128 bytes basis when it is possible. The host must take care that: * Requests from Host
Command Name Program Flash Program EEPROM Data Record Type 00h 07h Load Offset start address start address Record Length nb of Data nb of Data Data[0] x x ... ... ... Data[127] x x
The data to program transmitted within a frame are in the same page.
Answers from Bootloader
The bootloader answers with: * * * `.' & `CR' & 'LF' when the data are programmed `X' & `CR' & `LF' if the checksum is wrong `P' & `CR' & `LF' if the Security is set
Flow Description Host
Send Write Command
Bootloader Write Command
Wait Write Command
OR Wait Checksum Error COMMAND ABORTED
Checksum error
'X' & CR & LF
Send Checksum error
NO_SECURITY
OR Wait Security Error COMMAND ABORTED
'P' & CR & LF
Send Security error
Wait Programming
Wait COMMAND_OK COMMAND FINISHED
'.' & CR & LF
Send COMMAND_OK
Example Programming Data (write 55h at address 0010h in the Flash)
HOST BOOT LOADER : 01 0010 00 55 9A : 01 0010 00 55 9A . CR LF
11
4225B-8051-12/03
Read the Flash or EEPROM Data
The flow described below allows the user to read data in the Flash memory or in the EEPROM data memory. A blank check command is possible with this flow. The device splits into blocks of 16 bytes the data to transfer to the Host if the number of data to display is greater than 16 data bytes.
Requests from Host
Command Name Read Flash Blank check on Flash Read EEPROM Data 04h x 05h start address end Address Record Type Load Offset Record Length Data[0] Data[1] Data[2] Data[3] Data[4] 00h 01h 02h
Note:
The field 'Load offset' is not used.
Answers from Bootloader
The bootloader answers to a read Flash or EEPROM Data memory command: * * * * * * * `Address = data` & `CR' & 'LF' up to 16 data by line. `X' & `CR' & `LF' if the checksum is wrong `L' & `CR' & `LF' if the Security is set `.' & `CR' & 'LF' when the blank check is ok `First Address wrong' `CR' & `LF' when the blank check is fail `X' & `CR' & `LF' if the checksum is wrong `P' & `CR' & `LF' if the Security is set
The bootloader answers to blank check command:
Flow Description: Blank Check Command Host
Send Blank Check Command
Bootloader Blank Check Command
Wait Blank Check Command
OR Wait Checksum Error COMMAND ABORTED
Checksum Error
'X' & CR & LF
Send Checksum Error
Flash Blank
OR
Wait COMMAND_OK COMMAND FINISHED
'.' & CR & LF
Send COMMAND_OK
Wait Address Not Erased COMMAND FINISHED
address & CR & LF
Send First Address Not Erased
12
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Example Blank Check ok
HOST BOOT LOADER : 05 0000 04 0000 7FFF 01 78 : 05 0000 04 0000 7FFF 01 78 . CR LF
Blank Check ko at address xxxx
HOST BOOT LOADER : 05 0000 04 0000 7FFF 01 78 : 05 0000 04 0000 7FFF 01 78 xxxx CR LF
Blank Check with checksum error
HOST BOOT LOADER : 05 0000 04 0000 7FFF 01 70 : 05 0000 04 0000 7FFF 01 70 X CR LF CR LF
Flow Description: Read Command Host
Send Display Command
Bootloader Display Command
Wait Display Command
OR Wait Checksum Error COMMAND ABORTED
Checksum Error
'X' & CR & LF
Send Checksum Error
RD_WR_SECURITY
OR Wait Security Error COMMAND ABORTED
'L' & CR & LF
Send Security Error
Read Data
All Data Read
Complete Frame
Wait Display Data
"Address = " "Reading value" CR & LF
Send Display Data
All Data Read
All Data Read
COMMAND FINISHED
COMMAND FINISHED
Note:
The maximum size of block is 400h. To read more than 400h Bytes, the Host must send a new command.
13
4225B-8051-12/03
Example Display data from address 0000h to 0020h
HOST BOOT LOADER BOOT LOADER BOOT LOADER BOOT LOADER : 05 0000 04 0000 0020 00 D7 : 05 0000 04 0000 0020 00 D7 0000=-----data------ CR LF 0010=-----data------ CR LF 0020=data CR LF (16 data) (16 data) ( 1 data)
Program Configuration Information
The flow described below allows the user to program Configuration Information regarding the bootloader functionality. The Boot Process Configuration: - - - - - - BSB SBV P1_CF, P3_CF, P4_CF Fuse bits (BLJB and X2 bits) (see Section "Mapping and Default Value of Hardware Security Byte") SSB EB
Requests from Host
Command Name Erase SBV & BSB Program SSB level1 02h Program SSB level2 Program BSB Program SBV Program P1_CF Program P3_CF Program P4_CF Program EB Program bit BLJB 03h Program bit X2 0Ah 08h 03h x 03h 06h 03h 04h 06h 04h bit value 05h 01h 00h 01h 02h value Record Type Load Offset Record Length 02h Data[0] 04h Data[1] 00h 00h Data[2] -
Note:
1. The field 'Load Offset' is not used. 2. To program the BLJB and X2 bit the 'bit value' is 00h or 01h.
Answers from Bootloader
The bootloader answers with: * * * `.' & `CR' & 'LF' when the value is programmed `X' & `CR' & `LF' if the checksum is wrong `P' & `CR' & `LF' if the Security is set
14
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Flow Description Host
Send Write Command
Bootloader Write Command
Wait Write Command
OR Wait Checksum Error COMMAND ABORTED
Checksum error
'X' & CR & LF
Send Checksum error
NO_SECURITY
OR Wait Security Error COMMAND ABORTED
'P' & CR & LF
Send Security error
Wait Programming
Wait COMMAND_OK COMMAND FINISHED
'.' & CR & LF
Send COMMAND_OK
Example Programming Atmel function (write SSB to level 2)
HOST BOOT LOADER : 02 0000 03 05 01 F5 : 02 0000 03 05 01 F5. CR LF
Writing Frame (write BSB to 55h)
HOST BOOT LOADER : 03 0000 03 06 00 55 9F : 03 0000 03 06 00 55 9F . CR LF
15
4225B-8051-12/03
Read Configuration Information or Manufacturer Information Requests from Host
The flow described below allows the user to read the configuration or manufacturer information.
Command Name Read Manufacturer Code Read Family Code
Record Type
Load Offset
Record Length Data[0] Data[1] 00h 01h 00h 02h 03h 00h 01h 02h
Read Product Name Read Product Revision Read SSB Read BSB Read SBV Read P1_CF Read P3_CF Read P4_CF Read EB Read HSB (Fuse bit) Read Device ID1 0Eh Read Device ID2 Read Bootloader version 0Fh 0Bh 05h x 02h 07h
03h 04h 05h 06h 00h 00h 01h 00h
Note:
The field 'Load Offset' is not used
Answers from Bootloader
The bootloader answers with: * * * `value' & `.' & `CR' & 'LF' when the value is programmed `X' & `CR' & `LF' if the checksum is wrong `P' & `CR' & `LF' if the Security is set
16
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Flow Description Host
Send Read Command
Bootloader Read Command
Wait Read Command
OR Wait Checksum Error COMMAND ABORTED
Checksum error
'X' & CR & LF
Send Checksum error
RD_WR_SECURITY
OR Wait Security Error COMMAND ABORTED
'L' & CR & LF
Send Security error
Read Value
Wait Value of Data COMMAND FINISHED
'value' & '.' & CR & LF
Send Data Read
Example Read function (read SBV)
HOST BOOT LOADER : 02 0000 05 07 02 F0 : 02 0000 05 07 02 F0 Value . CR LF
Atmel Read function (read Bootloader version)
HOST BOOT LOADER : 02 0000 01 02 00 FB : 02 0000 01 02 00 FB Value . CR LF
17
4225B-8051-12/03
Erase the Flash
The flow described below allows the user to erase the Flash memory. Two modes of Flash erasing are possible: * * Full-chip erase Block erase
The Full Chip erase command erases the whole Flash (16 Kbytes) and sets some Configuration Bytes to their default values: * * * BSB = FFh SBV = FCh SSB = FFh (NO_SECURITY)
Take care that the full chip erase execution takes few seconds (128 pages )
The full chip erase is always executed whatever the Software Security Byte value is.
Note:
The Block erase command erases only a part of the Flash. Two Blocks are defined in the T89C5115: * * Requests from Host
Command Name Erase block0 (0k to 8k) 02h Erase block1 (8k to 16k) Full chip erase 03h x 01h 07h 01h 20h Record Type Load Offset Record Length Data[0] Data[1] 00h
block0 (from 0000h to 1FFFh) block1 (from 2000h to 3FFFh)
Answers from Bootloader
As the Program Configuration Information flows, the erase block command has three possible answers: * * * `.' & `CR' & 'LF' when the data are programmed `X' & `CR' & `LF' if the checksum is wrong `P' & `CR' & `LF' if the Security is set
18
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Flow Description Host
Send Erase Command
Bootloader Erase Command
Wait Erase Command
OR Wait Checksum Error COMMAND ABORTED
Checksum Error
'X' & CR & LF
Send Checksum error
NO_SECURITY
OR Wait Security Error COMMAND ABORTED
'P' & CR & LF
Send Security error
Wait Erasing
Wait COMMAND_OK COMMAND FINISHED
'.' & CR & LF
Send COMMAND_OK
Example Full Chip Erase
HOST BOOT LOADER : 01 0000 03 07 F5 : 01 0000 03 07 F5 . CR LF
Erase Block1(8k to 16k)
HOST BOOT LOADER : 02 0000 03 01 20 DA : 02 0000 03 01 20 DA . CR LF
19
4225B-8051-12/03
Start the Application
The flow described below allows to start the application directly from the bootloader upon a specific command reception. Two options are possible: * Start the application with a reset pulse generation (using watchdog). When the device receives this command the watchdog is enabled and the bootloader enters a waiting loop until the watchdog resets the device. Take care that if an external reset chip is used, the reset pulse in output may be wrong and in this case the reset sequence is not correctly executed. Start the application without reset A jump at the address 0000h is used to start the application without reset.
*
Requests from Host
Command Name Start application with a reset pulse generation 03h Start application with a jump at 'address' x 04h Record Type Load Offset Record Length 02h 03h 01h Address Data[0] Data[1] 00h Data[2] Data[3] -
Answer from Bootloader Example
No answer is returned by the device.
Start Application with reset pulse
HOST BOOT LOADER : 02 0000 03 03 00 F8 : 02 0000 03 03 00 F8
Start Application without reset at address 0000h
HOST BOOT LOADER : 04 0000 03 03 01 00 00 F5 : 04 0000 03 03 01 00 00 F5
20
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
In-Application Programming/Selfprogramming
The IAP allows to reprogram the microcontroller's on-chip Flash memory without removing it from the system and while the embedded application is running. The user application can call some Application Programming Interface (API) routines allowing IAP. These API are executed by the bootloader. To call the corresponding API, the user must use a set of Flash_api routines which can be linked with the application. Example of Flash_api routines are available on the Atmel web site on the software application note: C Flash Drivers for the T89C5115 The Flash_api routines on the package work only with the UART bootloader. The Flash_api routines are listed in APPENDIX-2.
API Call
Process The application selects an API by setting R1, ACC, DPTR0 and DPTR1 registers. All calls are made through a common interface 'USER_CALL' at the address FFF0h. The jump at the USER_CALL must be done by LCALL instruction to be able to comeback into the application. Before jump at the USER_CALL, the bit ENBOOT in AUXR1 register must be set. Constraints The interrupts are not disabled by the bootloader. Interrupts must be disabled by user prior to jump to the USER_CALL, then re-enabled when returning. Interrupts must also be disabled before accessing EEPROM Data then re-enabled after. The user must take care of hardware watchdog before launching a Flash operation. For more information regarding the Flash writing time see the T89C5115 datasheet.
API Commands
Several types of APIs are available: * * * * * Read/Program Flash and EEPROM Data memory Read Configuration and Manufacturer Information Program Configuration Information Erase Flash Start Bootloader
Read/Program Flash and EEPROM Data Memory
All routines to access EEPROM Data are managed directly from the application without using bootloader resources. To read the Flash memory the bootloader is not involved. For more details on these routines see the T89C5115 datasheet sections 'Program/Code Memory' and 'EEPROM Data Memory'. Two routines are available to program the Flash: - - __api_wr_code_byte __api_wr_code_page
21
4225B-8051-12/03
*
The application program load the column latches of the Flash then call the __api_wr_code_byte or __api_wr_code_page see data sheet in section 'Program/Code Memory'. Parameter Settings
API_name __api_wr_code_byte R1 02h DPTR0 Address in Flash memory to write Address of the first Byte to program in the Flash memory DPTR1 Address in XRAM of the first data to program Acc Value to write Number of Byte to program
*
__api_wr_code_page
09h
*
instruction: LCALL FFF0h.
No special resources are used by the bootloader during this operation
Note:
Read Configuration and Manufacturer Information
*
Parameter Settings
API_name __api_rd_HSB __api_rd_BSB __api_rd_SBV __api_rd_SSB __api_rd_EB __api_rd_manufacturer __api_rd_device_id1 __api_rd_device_id2 __api_rd_device_id3 __api_rd_bootloader_version R1 0Bh 07h 07h 07h 07h 00h 00h 00h 00h 0Fh DPTR0 0000h 0001h 0002h 0000h 0006h 0000h 0001h 0002h 0003h 0000h DPTR1 x x x x x x x x x x Acc return HSB return BSB return SBV return SSB return EB return manufacturer id return id1 return id2 return id3 return value
* *
Instruction: LCALL FFF0h. At the complete API execution by the bootloader, the value to read is in the api_value variable.
No special resources are used by the bootloader during this operation
Note:
Program Configuration Information
*
Parameter Settings
R1 0Ah 0Ah 0Ah 0Ah 06h 06h 06h 05h 05h DPTR0 0008h 0008h 0004h 0004h 0000h 0001h 0006h FFh FEh DPTR1 x x x x x x x x x Acc 00h 01h 00h 01h value to write value to write value to write x x
API Name __api_set_X2 __api_clr_X2 __api_set_BLJB __api_clr_BLJB __api_wr_BSB __api_wr_SBV __api_wr_EB __api_wr_SSB_LEVEL0 __api_wr_SSB_LEVEL1
22
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
API Name __api_wr_SSB_LEVEL2 R1 05h DPTR0 FCh DPTR1 x Acc x
*
Instruction: LCALL FFF0h.
1. See in the T89C5115 data sheet the time that a write operation takes. 2. No special resources are used by the bootloader during these operations
Note:
Erase Flash
The T89C5115 Flash memory is divided in to two blocks: Block 0: from address 0000h to 1FFFh Block 1: from address 2000h to 3FFFh These two blocks contain 64 pages. * Parameter Settings
R1 01h __api_erase_block1 2000h x x DPTR0 0000h DPTR1 x Acc x
API_name __api_erase_block0
*
Instruction: LCALL FFF0h.
1. See the T89C5115 data sheet for the time that a write operation takes, this time must be multiplied by the number of pages. 2. No special resources are used by the bootloader during these operations
Note:
Start Bootloader
This routine allows to start at the beginning of the bootloader as after a reset. After calling this routine the regular boot process is performed and the communication must be opened before any action. * * * No special parameter setting Set bit ENBOOT in AUXR1 register instruction: LJUMP or LCALL at address F800h
23
4225B-8051-12/03
Appendix-A
Table 3. Summary of Frames From Host
Command Program Nb Data Byte in Flash. Erase block0 (0000h-1FFFh) 02h Erase block1 (2000h-3FFFh) Start application with a reset pulse generation Start application with a jump at 'address' Erase SBV & BSB Program SSB level 1 Program SSB level 2 Program BSB Program SBV Program P1_CF 03h Program P3_CF Program P4_CF Program EB Full Chip Erase Program bit BLJB 03h Program bit X2 Read Flash Blank Check Read EEPROM Data 04h 05h x Start Address End Address x 01h x x x x x 0Ah 08h bit value 00h 01h 02h 07h 03h 02h 02h 04h x 03h x x x 05h x x x x 06h 03h 04h 06h 04h value value value bit value 01h 00h 01h 02h value value value 04h 01h 00h 00h address x 01h 20h 00h Record Type 00h Record Length nb of data (up to 80h) Offset start address Data[0] x Data[1] x 00h Data[2] x Data[3] x Data[4] x -
24
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Table 3. Summary of Frames From Host (Continued)
Command Read Manufacturer Code Read Family Code 00h Read Product Name Read Product Revision Read SSB Read BSB Read SBV Read P1_CF Read P3_CF Read P4_CF Read EB Read Hardware Byte Read Device Boot ID1 0Eh Read Device Boot ID2 Read Bootloader Version Program Nb Data byte in EEPROM 00h nb of data (up to 80h) start address 0Fh x 01h 00h x x x x 0Bh 05h 02h x 07h 02h 03h 00h 01h 02h 03h 04h 05h 06h 00h 00h Record Type Record Length Offset Data[0] Data[1] 00h 01h Data[2] Data[3] Data[4] -
25
4225B-8051-12/03
Appendix-B
Table 4. API Summary
Function Name __api_rd_code_byte __api_wr_code_byte Bootloader Execution no yes 02h Address in Flash memory to write Address of the first Byte to program in the Flash memory 0000h 2000h 0000h 0008h 0008h 0004h 0004h 0001h 0000h 0002h 0001h 0001h 0000h 00FFh 00FEh 00FCh 0006h 0006h 0000h 0001h 0002h 0003h 0000h Address in XRAM of the first data to program x x x x x x x x x x x x x x x x x x x x x x x Value to write R1 DPTR0 DPTR1 Acc
__api_wr_code_page
yes
09h
Number of Byte to program x x return value 00h 01h 00h 01h return value value return value value FCh return value x x x return value value return value return value return value return value return value
__api_erase_block0 __api_erase_block1 __api_rd_HSB __api_set_X2 __api_clr_X2 __api_set_BLJB __api_clr_BLJB __api_rd_BSB __api_wr_BSB __api_rd_SBV __api_wr_SBV __api_erase_SBV __api_rd_SSB __api_wr_SSB_level0 __api_wr_SSB_level1 __api_wr_SSB_level2 __api_rd_EB __api_wr_EB __api_rd_manufacturer __api_rd_device_id1 __api_rd_device_id2 __api_rd_device_id3 __api_rd_bootloader_version __api_eeprom_busy __api_rd_eeprom_byte __api_wr_eeprom_byte __api_start_bootloader
yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes no no no no
01h 01h 0Bh 0Ah 0Ah 0Ah 0Ah 07h 06h 07h 06h 06h 07h 05h 05h 05h 07h 06h 00h 00h 00h 00h 0Fh
26
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Datasheet Change Log
Changes from 4225A 03/03 to 4225B 12/03
1. Added bit stop for the UART protocol.
27
4225B-8051-12/03
28
T89C5115 UART Bootloader
4225B-8051-12/03
T89C5115 UART Bootloader
Table of Contents
Features ................................................................................................. 1 Description ............................................................................................ 1 Functional Description......................................................................... 2
In-System Programming (ISP) Capability ............................................................. In-Application Programming or Self-programming capability................................ Block Diagram ...................................................................................................... Bootloader Configuration ...................................................................................... Security................................................................................................................. Software Boot Vector............................................................................................ FLIP Software Program ........................................................................................ 2 2 2 3 4 5 5
In-System Programming ...................................................................... 6
Boot Process ........................................................................................................ 6 Physical Layer .......................................................................................................8 Protocol..................................................................................................................9
In-Application Programming/Self-programming ............................. 21
API Call............................................................................................................... 21 API Commands................................................................................................... 21
Appendix-A.......................................................................................... 24 Appendix-B.......................................................................................... 26 Datasheet Change Log ....................................................................... 27
Changes from 4225A - 03/03 to 4225B 12/03 .................................................... 27
Table of Contents .................................................................................. i
i
4225B-8051-12/03
Atmel Corporation
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600
Atmel Operations
Memory
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759
Regional Headquarters
Europe
Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500
Microcontrollers
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60
Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom
Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80
Asia
Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743
Japan
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581
Literature Requests
www.atmel.com/literature
Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems.
(c) Atmel Corporation 2003. All rights reserved. Atmel(R) and combinations thereof are the registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.
Printed on recycled paper.
4225B-8051-12/03 /xM

▲Up To Search▲

Price & Availability of T89C511503

	To Download T89C511503 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .